Fixturlaser AT-200

With the Fixturlaser AT-200 you perform alignments using two digital measuring units and a tablet or phone. There are free apps available for both Android and iOS, which can be downloaded from the store.

The measuring heads of the Fixturlaser AT-200 have a 30mm detector, so that coarse alignment is not necessary. Due to the digital levels, it is not necessary to rotate the shaft over 180 degrees.

User-friendly alignment equipment

The free app can be downloaded from the Playstore or from the App Store. The measuring heads are connected via Bluetooth, after which the measurement starts.

The graphical user interface guides the user through the alignment. The colour-coded alignment results give a clear picture of the position of the machine.

From the app you can make a PDF report with all relevant data such as softfoot measurement and alignment result. Photos can also be added to the report. You can place your own logo on the report.

app-h-31-result-out-of-tol-w-tv-rev-b-1024x576
7-0564-01-whats-in-the-case-at-200
meetkoppen-nxa
Expandable to machine diagnostics

The Fixturlaser AT-200 is expandable with additional hardware for performing additional measurements:

Pre-alignment

Hardware and software for measuring run-out, bearing clearance and softfoot. With the measuring probe (accuracy 0.001mm) various measuring points are taken. The free software reports the findings.

 

Machine diagnostics

With a wireless, tri-axial vibration sensor, measurements are taken to analyze the status of the rotating equipment. The free software provides an analysis of the problem (including alignment error, imbalance, looseness, cavitation) and overall values at all measuring points in 3 directions.

quick-guide-11-m7-and-s7-distance-utan-matt
Contents

AT-200 package with case

2 pcs of digital alignment sensors
2 pcs of V-brackets complete with chain
Extension fixture, 49 mm
Magnetic base
Rod kit
2 pcs of chains, 8 mm, 60 links (L=970 mm)
Tape measure, 5 m
2 pcs of angled universal tools
External power cable, EU, 2 m
External power cable, US, 2 m
2 pcs of USB-cables, A-mini B, 2 m
Power supply 5 USB-ports 5 VDC
Technical specifications

S7/ M7

Housing Material: Anodized Aluminum frame and high impact ABS plastic

overmolded with TPE rubber

Operating Temp: -10 to 50°C (14 to 122°F)

Storage Temp: -20 to 70°C ( -4 to 158°F)

Battery Charging Temp: 0 to 40°C ( 32 to 104°F)

Relative humidity: 10 – 90%

Weight: M7: 212 g (7,5 oz) S7: 188 g (6,6 oz)

Dimensions: 92mm x 77mm x 33mm (3,6 in x 3,0 in x 1,3 in)

Environmental protection: IP 65 (Dust tight and protected against water jets)

Laser: 650 nm class II diode laser

Laser line fan angle: 6°

Laser line divergence (full

angle):

0.25 mrad

Laser power: < 1 mW

Measurement distance: Up to 10m

Detector: 2nd gen. digital sensor

Detector length: 30mm ( 1,2 in )

Detector resolution: 1 μm

Measurement accuracy: 0,3% ± 7 μm

Signal processing: Digital signal processing with Sidespot rejection, edge

detection, ambient light elimination and anti-vibration mode

Inclinometer: Dual High Performance MEMS inclinometers

Inclinometer resolution: 0,01°

Inclinometer accuracy: ±0,2°

Wireless communication: Class I Bluetooth transmitter

Communication range: 10 m (33 ft)

Charging: 5V, 0,5A

Power supply: High performance Li Ion battery or external power.

Operating time: 17 hours continuous use (measuring)

Battery Charging time (system

off, room temperature):

8 h